A Wearable Gas Sensor For Health And Environmental Monitoring
January 24, 2020 | Penn State Materials Research InstituteEstimated reading time: 3 minutes
A highly sensitive wearable gas sensor for environmental and human health monitoring may soon become commercially available, according to researchers at Penn State and Northeastern University.
The sensor platform is an improvement on existing wearable sensors because it uses a self-heating mechanism that enhances sensitivity and allows for quick recovery and reuse of the platform. Other sensor platforms require an external heater. In addition, other wearable sensors require an expensive and time-consuming lithography process under cleanroom conditions.
“People like to use nanomaterials for sensing because their large surface to volume ratio makes them highly sensitive,” said Huanyu Cheng, assistant professor of engineering science and mechanics and materials science and engineering, Penn State. “The problem is the nanomaterial is not something we can easily hook up to with wires to receive the signal, necessitating the need for something called interdigitated electrodes, which are like the digits on your hand.”
In their new work, Cheng and his team use a laser to pattern a highly porous single line of nanomaterial similar to graphene for gas, biomolecules and in the future chemical sensing. In the non-sensing portion of the platform, they create a series of serpentine lines that they coat with silver. When they apply an electrical current, the gas sensing region will locally heat up due to its significantly larger electrical resistance, eliminating the need for a heater. The serpentine lines allow the platform to stretch like springs to adjust to the flexing of the body for wearable sensors.
The nanomaterials used in this work are reduced graphene oxide and molybdenum disulfide, or a combination of the two, or a metal oxide composite consisting of a core of zinc oxide and a shell of copper oxide, representing the two classes of widely used gas sensor materials (i.e., low-dimensional and metal oxide nanomaterials).
“Using a CO2 laser, often found in machine shops, we can easily make multiple sensors on our platform,” Cheng said. “We plan to have tens to a hundred sensors, each selective to a different molecule, like an electronic nose, to decode multiple components in a complex mixture.”
The US Defense Threat Reduction Agency (DTRA) is interested in this wearable sensor to detect chemical and biological agents that could damage the nerves or lungs. A medical device company is also working with the team to scale up production for patient health monitoring, including gaseous biomarker detection from the human body and environmental detection of pollutants that can affect the lungs.
Ning Yi, a Ph.D. student in Chen’s lab and co-lead author of a new paper posted online in the Journal of Materials Chemistry A, said, “In this paper, we showed that we could detect nitrogen dioxide, which is produced by vehicle emissions. We can also detect sulfur dioxide, which, together with nitrogen dioxide, causes acid rain. All these gases can be an issue in industrial safety.”
Their next step is to create high-density arrays and try some ideas to improve the signal and make the sensors more selective. This may involve using machine learning to identify the distinct signals of individual molecules on the platform.
The forthcoming print version of the journal will feature this paper with their image on its back cover. Other authors on the paper, titled “Novel gas sensing platform based on a stretchable laser-induced graphene pattern with self-heating capabilities” are visiting scientist and co-first author Li Yang, Jia Zhu, a Ph.D. student in Cheng’s group, Hongli Zhu, an assistant professor at Northeastern University and her student Zheng Cheng, and Xueyi Zhang, assistant professor of chemical engineering and his Ph.D. student Xinyang Yin, Penn State.
Funding was provided by start-up funding and seed grants at Penn State and Northeastern, and National Science Foundation. A provisional patent has been applied for.
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?