VTT: Environmental Impact of Flexible Electronics Can be Reduced by Almost 90%
March 1, 2023 | VTT Technical Research Centre of FinlandEstimated reading time: 2 minutes
VTT Technical Research Centre of Finland announces the results of a study investigating how changing the manufacturing of electronics can improve their environmental impact. For example, one of the project’s most significant findings showed that environmental impact could be reduced by 86% when additive printing methods are used to create flexible electronic components, as reported in detail by LUT University.
The project showed several areas of electronics manufacturing where an impact on environmental footprint and sustainability is possible.
“Traditionally, metal electronics parts are etched out of copper sheets in a process called PCB etching. The process removes unwanted copper from a printed circuit board, so only the required circuit remains while the rest of the sheet isn’t used,” says Liisa Hakola, Senior Scientist and Senior Project Manager at VTT.
“We found that flexible metal electronics parts can instead be printed onto bio-based substrates, like paper or bio-plastic. The process requires less energy and avoids the use of harmful chemicals while drastically reducing material waste and increasing the use of renewable materials. This change in the manufacturing process is the single largest factor in potentially reducing the climate impact of flexible electronics.”
In printed electronics, there are additional challenges that still need to be resolved. Silver has a high environmental impact and is commonly used for printed electronics. The project found that silver can be replaced with more abundant and less valuable alternatives, such as copper or carbon-based materials. This provides further reduction to the environmental footprint of flexible electronics. In addition, end-of-life management and longevity of product usability, i.e., better durability and decreased energy consumption, are also key factors in creating more sustainable electronics.
The flexible electronics market is expected to grow to $45.88 billion by 2026. By 2030, global electronic waste will reach 74 billion kilograms, with only 20% collected or recycled properly. The electronics industry is currently facing major challenges with the availability of crucial materials combined with increasing pressure to cut its environmental footprint and move toward circularity.
In March 2022, the European Commission published its Sustainable Products Initiative, which aims to ensure that all products placed on the EU market become more sustainable. Thereby, the initiative also includes electronics, and so manufacturers are met with increasing pressure to meet new sustainability requirements in the years to come.
“At VTT, our goal is to set a new standard for sustainability in the electronics industry and offer solutions that increase circularity at every stage of the electronics life cycle,” says Maria Smolander, Research Team Leader at VTT. “Implementing these new manufacturing methods on a mass scale is a challenge that the industry will inevitably need to tackle in the coming decade in order to keep up with increasingly strict regulations and demands from consumers.”
This national ecosystem project was co-funded by Business Finland.
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Factory Analytics
04/24/2024 | I-Connect007 Editorial TeamIn our fast-changing, deeply competitive, and margin-tight industry, factory analytics can be the key to unlocking untapped improvements to guarantee a thriving business. On top of that, electronics manufacturers are facing a tremendous burden to do more with less. If you don't already have a copy of this book, what follows is an excerpt from the introduction chapter of 'The Printed Circuit Assembler’s Guide to... Factory Analytics: Unlocking Efficiency Through Data Insights' to whet your appetite.
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
Winner of The Science Show Rakett 69 Receives Incap Scholarship
04/24/2024 | IncapThe winner of the Rakett 69 science show, Andri Türkson, who stood out as an electronics enthusiast, received a scholarship from Incap Estonia, along with an internship opportunity in Saaremaa.
Alternative Manufacturing Inc. Awarded QML Requalification to IPC J-STD-001 and IPC-A-610
04/24/2024 | IPCIPC's Validation Services Program has awarded an IPC J-STD-001 and IPC-A-610 Qualified Manufacturers Listing (QML) requalification to Alternative Manufacturing Inc (AMI).