Coated Ultra-Thin Copper on Printed Circuit Laminates
July 16, 2015 | Intrinsiq Materials Inc.Estimated reading time: 5 minutes
Figures 2, 3 and 4 show examples of the raw coated material, followed by sintering and the finished circuit, respectively. The samples were pattern plated with copper, then tin etch resist. The photo resist was stripped off; the circuit was etched in industry standard equipment with ammonia based solution. The tin was stripped off after etching resulting in a copper circuit. The coupons were tested for peel strength and showed a 1.2 N/cm average. Note that the coupons used for the test are industry standard patterns as designated by IPC.
The electroplated copper was also subjected to pull testing to verify adhesion to the base coating of copper. The result of this test was that the pull strength exceeded the detection limit of the device.
The sintered nano-copper, thin-film coating will also auto catalyze in standard PCB electro-less copper solutions. This seed layer technology replaces the palladium catalyst currently used to initiate electro-less copper in the PCB industry.
Similar process development is underway for rigid laminates and alumina as well. Initial testing shows comparable pull and peel strength to currently available laminates. This thin film coating also allows lower temperature processing of the ceramic laminates than current firing methods using precious metal pastes.
Conclusion
Nanocopper based copper foil has great promise for high-density microcircuits. Utilizing conventional coating capability, volume production is easily scalable and cost-effective.
David Ciufo is the PCB program manager at Intrinsiq Materials Inc. a recognized leader in nanomaterials development.
Page 2 of 2Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.