Flexible Thinking: Process Engineering—PCB Manufacturing’s ‘Delta Force’
May 13, 2016 | Joe Fjelstad, Verdant ElectronicsEstimated reading time: 1 minute
The role of the process engineer is arguably one of the most important jobs in the printed circuit industry. The process engineer is on the front line of manufacturing and responsible for making sure product yields and profitability meet expectations. The job typically entails and intertwines many different and even disparate disciplines, including: electrochemistry, mechanical engineering, NC machining, robotics and automation, metallurgy, laser technology, polymer processing and photolithography. It even reaches back into the printed circuit design process. Because of this variety, it is also arguably at once, one of the most challenging and interesting jobs in the PCB industry.
In practice in most major manufacturing facilities, process engineers often specialize in just one of the areas identified here. In smaller facilities, the process engineer often must move between and attend to matters in more than one discipline, most commonly process steps which immediately precede or follow the area where the engineer has special training and expertise. However, in many cases, factors which may influence product quality and yield may be several steps earlier or later in the process. This is extremely important when one is looking into, or in the midst of implementing a new process on the manufacturing floor. Change comes slowly in PCB manufacturing and old habits are hard to break, so keeping a finger on the pulse of the process is critical.
It is a simple fact of life that in PCB manufacturing, process characterization, monitoring and maintenance are critical to success, and so also is collecting and evaluating data on process health. The tools and specific methods and measurements required will vary significantly from process to process, but without control, the quality of the results of the process will be left to a roll of the dice.
Editor's Note: This article originally appeared in the April 2016 issue of The PCB Magazine
Suggested Items
Real Time with… IPC APEX EXPO 2024: Tools, Training, and Trends in Manufacturing Engineering
04/25/2024 | Real Time with...IPC APEX EXPOGuest Editor Kelly Dack and Product Specialist Erik Bateham of Polar Instruments discuss Polar's latest technology, including their role in aiding manufacturing engineers. They highlight the advanced capabilities of Polar's tools and the critical role of signal integrity analysis, as well as the importance of accurate modeling in board manufacturing. Polar's unique training approach and demonstration contact details are also explored.
TTM Celebrates the Grand Opening of Its First Manufacturing Facility in Penang
04/25/2024 | TTM Technologies, Inc.TTM Technologies, Inc., a leading global manufacturer of technology solutions including mission systems, radio frequency (RF) components and RF microwave/microelectronic assemblies, and quick-turn and technologically advanced printed circuit boards (PCBs), officially opened its first manufacturing plant in Penang, Malaysia with an investment of USD200 million (approximately RM958 million).
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
Fujitsu, METRON Collaborate to Drive ESG Success
04/24/2024 | JCN NewswireFujitsu Limited and METRON SAS, a French cleantech company specializing in energy management solutions for industrial decarbonization, today announced a strategic initiative to contribute to the realization of carbon neutrality in the manufacturing industry.