FKN Systek's N100 Nibbler Available with Three Blade Types
September 9, 2019 | FKN SystekEstimated reading time: 1 minute
Singulating tab routed printed circuit cards in low to medium volume production quantities is safe and easy with the N100 Nibbler from FKN Systek. Three blade types are available in standard thicknesses of 0.120 in, 0.093 in and 0.062 in.
Custom sizes to match the width of the routed section can be ground on request. Tabs up to 0.324” (8.23 mm) are cut cleanly on each side so that no further clean-up is required to remove excess material, as is often the case when using hand tools or when breaking the panels manually. In addition, since only one tab is cut at a time, minimal stress is imparted to the board during the process as the panel is not pressed between two points during the cut.
The N100 is provided with a quick-connect pneumatic port which plugs directly into factory air (80-100 PSI). Stepping on a foot pedal activates the cutting process. The excess material from the tab is stored inside a compartment of the tool and can be easily removed at the convenience of the operator. To see a video of the N100 and other depaneling methods go to fknsystek.com.
The Sharp Blade support dies of the N100 provide a clean shearing action, ideal for singulating one tab at a time on flex circuit boards. This is the perfect tool for low volume singulation of a variety of flex circuit and standard PCBs built on a rectangular pattern.
Come by booth 107 at SMTAI Rosemont, September 24 and 25 to see FKN Systek Depaneling tools. Bring samples for evaluation.
Suggested Items
Three Industry Leaders Receive IPC President’s Award
04/17/2024 | IPCIn recognition of their leadership and significant contributions of time and talent to IPC and the electronics industry, three IPC volunteers were presented with the IPC President’s Award at IPC APEX EXPO in Anaheim, Calif., on April 9, 2024.
Marcy's Musings: The Growing Industry
04/16/2024 | Marcy LaRont -- Column: Marcy's MusingsAfter decades of steady decline in the U.S. and Europe, the PCB industry is finally growing, especially in China Plus One countries. The U.S. for example, which seemed to have abdicated its title as the world leader in innovating high-technology cutting-edge manufacturing processes, is now in a race to regain what it lost and then some. The PCB fabrication industry is growing in the West, thanks to DoD funding, the CHIPS and Science Act, and hopefully, the passing of HR 3249, the Printed Circuit Board and Substrates Act.
FTG Announces Q1 2024 Financial Results
04/12/2024 | Firan Technology Group CorporationDuring Q1 2024, the Corporation has continued to invest in technology in existing sites, grow the business organically, and integrate the two acquisitions completed last year. FTG is strategically deploying its capital in ways that will drive increased shareholder returns for the future in both the near term and long term. Specifically, FTG accomplished the following in Q1 2024, which continues to improve the Corporation and position it for the future:
An Ultimate Goal in Sustainability: Recyclable PCBs
04/11/2024 | Marcy LaRont, PCB007 MagazineWho doesn’t believe in recycling? “Re-use, repurpose, recycle” has been a drumbeat for more than two decades. Our children learn about it in primary school. Full university departments devoted to environmental science and sustainability in universities forward their discipline for the world's benefit. In theory, we all get behind the concept of recycling, even if the nuances of execution may fall short.
DuPont Unveils Pyralux ML Laminate Series, Offering High Thermal Management for Extreme Environments
04/09/2024 | DuPontDuPont introduced the DuPont™ Pyralux® ML Series of double-sided metal-clad laminates, a unique addition to its extensive family of Pyralux® laminates for flexible and rigid-flex printed circuit boards (PCBs).